Shopping

Help keep fine dirt and debris out of your helmet and suit without interfering with Head & Neck Restraints!
• FR Acrylic/Cotton Blended 6.5oz/yd²
• Single Layer Construction
• Breathable Material
• Plush Feel

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.

Z-20 Shield Replacement:
*NOTE: DO NOT USE power tools or overtighten screws when changing shields.
• Step 1 - Lay a towel on a flat surface and set the helmet on it.
• Step 2 - Remove the shield pivot tensioners on each side. (This is the smaller screw on the sides of the shield.)
• Step 3 - Remove the shield pivot screws on each side. (This is the larger screw on the sides of the shield. For best results, we suggest using a quarter to loosen/tighten these screws.)
• Step 4 - Remove the shield. We suggest using a soft cloth towel to wipe down the rubber seal as well as where the shield mounts to the helmet for best results.
• Step 5 - Place the new shield on the helmet. There are two white washers that go between the shield and helmet, make sure these are in place before re-installing the shield pivot screws.
• Step 6 - Hand thread the shield pivot screws to hold the shield in place. Once hand threaded, use a quarter to tighten until snug with the helmet shell. Do not overtighten.
• Step 7 - Hand thread the shield pivot tensioners, then tighten to desired tension for shield movement.

Introducing the ZR-Drag Race Shoes, lightweight shoes built with high-quality materials at an affordable price for drag racing.
• RS006C01 - Black
• RS006C01W - Black WIDE
• Lightweight Aramid Construction
• Leather outer shell
• SFI 3.3/20 Certified

• Lightweight Aramid Construction
• Double Velcro Enclosure for easy on & off
• Durable rubber sole for top performance
• SFI 3.3/20 Certified

• Lightweight Aramid Construction
• Pre-curved Fingers
• Elastic Band and Velcro enclosure
• Leather pads on palms and fingers for grip
• SFI 3.3/20 certified

• 9-Layer Lightweight Aramid Construction
• Built-in Arm Restraints
• Box Quilt Stitching
• Pockets on each leg
• Adjustable Belt
• Aramid Cuffs for added comfort around wrists and ankles
• Shoulder flex panels allow for fully floating 360 degree arm rotation
• Bootcut provides stylish ankle protection
• SFI 3.2A/20

• 9-Layer Lightweight Aramid Construction
• Built-in Arm Restraints
• Snap and Loop System to attach ZR-Drag Pants
• Box Quilt Stitching
• Aramid Cuffs for added comfort around wrists
• Shoulder flex panels allow for fully floating 360 degree arm rotation
• SFI 3.2A/20